|
Last Modified:
08-30-2021
|
6.10:8.0.50
|
Doc ID:
RM100000001FS6Z
|
|
Model Year Start:
2019
|
Model:
Prius
|
Prod Date Range:
[12/2018 - 07/2020]
|
|
Title:
INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL; 2019 - 2020 MY Prius [12/2018 - 07/2020]
|
REMOVAL
PROCEDURE
1. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
(a) Remove the tonneau cover assembly.
2. REMOVE REAR NO. 1 FLOOR BOARD
(a) Remove the rear No. 1 floor board.
3. REMOVE DECK BOARD RETAINER (except 2WD without Spare Tire)
(a) for LH Side:
|
Remove in this Direction
|
(1) Disengage the clip and guide to remove the deck board retainer as shown in the illustration.
(b) for RH Side:
|
Remove in this Direction
|
(1) Disengage the clip and guide to remove the deck board retainer as shown in the illustration.
4. REMOVE DECK FLOOR BOX LH (for 2WD without Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
5. REMOVE DECK FLOOR BOX RH (for 2WD without Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
6. REMOVE REAR DECK FLOOR BOX (for 2WD with Compact Spare Tire)
(a) Remove the rear deck floor box.
7. REMOVE DECK FLOOR BOX LH (for 2WD with Compact Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
8. REMOVE DECK FLOOR BOX RH (for 2WD with Compact Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
9. REMOVE DECK FLOOR BOX RH (for 2WD with Full Size Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
10. REMOVE DECK FLOOR BOX LH (for 2WD with Full Size Spare Tire)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
11. REMOVE REAR DECK FLOOR BOX (for AWD)
|
(a) Using a clip remover, remove the clip and rear deck floor box.
|
|
12. REMOVE DECK FLOOR BOX LH (for AWD)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
13. REMOVE DECK FLOOR BOX RH (for AWD)
(a) Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
|
*a
|
Protective Tape
|
|
Turn in this Direction
|
|
Remove in this Direction
|
14. REMOVE DECK TRIM SERVICE HOLE COVER
Click here
15. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)
(b) Disengage the 2 guides to remove the 2 luggage hold belt striker assemblies.
16. REMOVE REAR DECK TRIM COVER
(a) Disengage the 4 clips and 2 guides to remove the rear deck trim cover as shown in the illustration.
|
Remove in this Direction
|
17. REMOVE FRONT DOOR SCUFF PLATE LH
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
HINT:
Use the same procedure for the front side and rear side.
(b) Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.
|
Remove in this Direction
|
18. REMOVE COWL SIDE TRIM BOARD LH
(a) Remove the clip.
|
Remove in this Direction
|
(b) Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.
19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
20. REMOVE FRONT PILLAR GARNISH LH
(a) Apply protective tape around the front pillar garnish LH as shown in the illustration.
|
Protective Tape
|
(b) Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.
HINT:
Let the front pillar garnish LH hang from the front pillar garnish clip.
|
*1
|
Front Pillar Garnish Clip
|
|
Place Hand Here
|
|
Remove in this Direction
|
(c) While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
|
*1
|
Front Pillar Garnish Clip
|
|
Remove in this Direction
|
NOTICE:
The front pillar garnish clip is reusable if it is not damaged.
(d) When the front pillar garnish clip cannot be disengaged easily:
(1) While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.
|
Move in this Direction
|
(2) While pulling the front pillar garnish clip as shown in the illustration push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.
NOTICE:
If the front pillar garnish clip is damaged, replace it with a new one.
|
Pull in this Direction
|
(e) Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
|
Remove in this Direction
|
|
(f) Protect the curtain shield airbag assembly LH.
(1) Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.
NOTICE:
Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.
|
|
|
*1
|
Curtain Shield Airbag Assembly LH
|
|
*a
|
Protective Cover
|
|
*b
|
Adhesive Tape
|
|
|
21. REMOVE REAR DOOR SCUFF PLATE LH
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
(b) Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.
|
Remove in this Direction
|
22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
23. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
Click here
24. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
25. REMOVE LOWER CENTER PILLAR GARNISH LH
(a) Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).
|
*a
|
Claw (A)
|
|
*b
|
Claw (B)
|
|
Place Hand Here
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(b) Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).
(c) Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
26. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH
|
(a) Using a clip remover, remove the 2 clips.
|
|
(b) Disengage the guide as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
(c) Disengage the clip and 2 guides to remove the center pillar garnish assembly LH as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
27. REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
28. REMOVE COWL SIDE TRIM BOARD RH
HINT:
Use the same procedure as for the LH side.
29. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
30. REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
31. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
32. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
33. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
34. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
35. REMOVE LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
36. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
37. REMOVE REAR SEAT ASSEMBLY
Click here
38. REMOVE REAR UNDER SIDE COVER LH
(a) Remove the 2 clips.
|
Remove in this Direction
|
(b) Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.
39. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
|
(a) Loosen the bolt to remove the rear seatback hinge sub-assembly LH.
|
|
40. REMOVE REAR SEAT SIDE GARNISH LH
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here
|
|
Remove in this Direction
|
(b) Disengage the 2 clips and 2 guides to remove the rear seat side garnish LH as shown in the illustration.
|
Remove in this Direction
|
41. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
(b) Disengage the guide to remove the luggage hold belt striker assembly.
42. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for LH Side)
(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 1 tonneau cover holder cap as shown in the illustration.
|
*a
|
Protective Tape
|
|
Insert Screwdriver Here
|
|
Remove in this Direction
|
43. REMOVE TONNEAU COVER HOOK A (for LH Side)
(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the tonneau cover hook A as shown in the illustration.
|
*a
|
Protective Tape
|
|
Insert Screwdriver Here
|
|
Remove in this Direction
|
44. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
(a) Lower the No. 2 luggage compartment trim hook as shown in the illustration.
|
|
|
*1
|
No. 2 Luggage Compartment Trim Hook
|
|
|
(b) Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.
|
*1
|
No. 2 Luggage Compartment Trim Hook
|
|
*a
|
Protective Tape
|
|
*b
|
Hole (A)
|
|
*c
|
Clip
|
|
Insert Screwdriver Here
|
|
Remove in this Direction
|
HINT:
Insert the screwdriver into the hole (A).
(d) Disengage the 5 claws, 2 clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.
|
Remove in this Direction
|
-
|
-
|
46. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH
(a) Disengage the 5 clips as shown in the illustration to remove the roof side inner garnish assembly LH.
|
Remove in this Direction
|
-
|
-
|
47. REMOVE REAR UNDER SIDE COVER RH
HINT:
Use the same procedure as for the LH side.
48. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
49. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
50. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
HINT:
Use the same procedure as for the LH side.
51. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for RH Side)
HINT:
Use the same procedure as for the LH side.
52. REMOVE TONNEAU COVER HOOK A (for RH Side)
HINT:
Use the same procedure as for the LH side.
53. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
54. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
55. REMOVE ROOF CONSOLE BOX ASSEMBLY
Click here
56. REMOVE NO. 1 ROOM LIGHT ASSEMBLY
Click here
57. REMOVE SENSOR COVER (w/ Humidity Sensor)
Click here
58. REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)
Click here
59. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
Click here
60. REMOVE RAIN SENSOR (w/ Rain Sensor)
Click here
61. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Inner Rear View Mirror Stay Holder Cover)
Click here
62. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)
Click here
63. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense)
Click here
64. REMOVE ASSIST GRIP ASSEMBLY
HINT:
Use the same procedure for all assist grip sub-assemblies.
|
(a) Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
SST: 09813-00010
NOTICE:
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
|
|
(b) Pull SST as shown in the illustration to disengage the claw.
NOTICE:
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
|
*a
|
30 to 45°
|
|
Pull in this Direction
|
HINT:
-
Use the same procedure for the claw on the other side of the assist grip cover LH.
-
Use the same procedure for the LH side and RH side.
(c) Remove the assist grip cover LH.
HINT:
Use the same procedure for the LH side and RH side.
(d) Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.
|
Remove in this Direction
|
(e) Remove the 2 clips from the vehicle body.
65. REMOVE REAR ASSIST GRIP ASSEMBLY LH
HINT:
Use the same procedure as for the assist grip assembly.
66. REMOVE REAR ASSIST GRIP ASSEMBLY RH
HINT:
Use the same procedure as for the assist grip assembly.
67. REMOVE VISOR BRACKET COVER (for LH Side)
(a) Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover.
|
Insert Moulding Remover Here
|
68. REMOVE VISOR ASSEMBLY LH
(b) Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder.
|
*1
|
Visor Holder
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(c) Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
69. REMOVE VISOR HOLDER LH
(a) Turn the visor holder approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.
|
*a
|
45°
|
|
Remove in this Direction (1)
|
|
Remove in this Direction (2)
|
(b) Disengage the 2 claws to remove the base of the visor holder LH.
70. REMOVE VISOR BRACKET COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
71. REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
72. REMOVE VISOR HOLDER RH
HINT:
Use the same procedure as for the LH side.
73. REMOVE ROOF HEADLINING ASSEMBLY
(a) for Windshield Glass Side:
(1) Disconnect each connector.
(b) for Front Pillar LH Side:
(1) Remove the protective cover.
|
(2) Using a clip remover, disengage the 4 clamps.
|
|
(3) Disconnect the 2 connectors.
(4) Install the protective cover.
(c) for Front Pillar RH Side:
(1) Remove the protective cover.
|
(2) Using a clip remover, disengage the 3 clamps.
|
|
(3) Disconnect each connector.
(4) Install the protective cover.
|
(d) for Rear Pillar RH Side:
(1) Disconnect the 2 connectors.
|
|
(e) for Roof Side (w/o Sliding Roof):
(1) Using a clip remover, remove the 3 clips.
(f) for Roof Side (w/ Sliding Roof):
|
*a
|
Fastener
|
*b
|
Guide
|
|
*c
|
Clamp
|
-
|
-
|
(1) Using a clip remover, disengage the clamp.
(2) Disconnect the connector.
(3) Using a clip remover, remove the 3 clips.
(4) Disengage the 6 fasteners and guide.
(g) Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
NOTICE:
Do not damage the roof headlining assembly or vehicle interior.
|
Remove in this Direction
|
|